A solar battery health check can show whether disappointing performance is caused by genuine capacity loss, a measurement issue, changed settings or another system fault. This guide provides a repeatable UK-friendly routine for tracking usable capacity, charge and discharge behaviour, efficiency, temperature, firmware events and warranty evidence without opening or modifying the battery.
Overview
Solar batteries gradually change with use and age, but a single low reading does not prove that a battery is failing. Solar generation varies by season, household demand changes, and the battery management system may reserve part of the battery’s nominal capacity to protect it. The first task is therefore to establish what your system is designed to report.
Nominal capacity is the battery’s stated total energy capacity. Usable capacity is the amount available to the home after the manufacturer’s operating limits, reserve and state-of-charge protections are applied. A battery marketed with a particular nominal capacity may therefore show a smaller usable figure in the monitoring app. Always compare like with like and check the product documentation before deciding that capacity has been lost.
A useful health check combines app records with controlled observations. It should help you answer four questions:
- Is the battery reaching the expected state of charge when there is enough available energy?
- How much energy does it deliver during a measured discharge?
- Has round-trip efficiency or usable capacity changed consistently over time?
- Are temperature, alarms, firmware changes or installation issues affecting the result?
Do not remove covers, disconnect cables, bypass protections or attempt an internal battery test. Batteries can contain hazardous voltages even when the solar panels are not producing. Use the manufacturer’s instructions and ask the original installer or a suitably qualified battery professional to investigate physical faults, repeated alarms or unusual heat.
What to track
1. State of charge and energy flows
Record the battery’s state of charge, usually shown as a percentage, alongside the energy entering and leaving it. Note whether the figure comes from the battery, inverter or monitoring app, since different systems may calculate values differently. Record the date, time, weather, operating mode and any unusual household loads.
Useful readings include:
- State of charge at the start and end of a test.
- Energy charged into the battery.
- Energy discharged from the battery to the home or designated backup circuit.
- Solar generation, grid import and export during the same period.
- Any minimum reserve or backup setting.
A battery that never reaches its normal upper state of charge may not have lost capacity. It may instead be limited by low solar generation, a time-of-use schedule, a reserve setting or an inverter control rule.
2. Measured usable capacity
For a practical discharge check, begin with the battery near its normal full operating point and record the state of charge. Allow it to discharge through ordinary household demand until it reaches its configured minimum, then record the energy supplied by the battery. Avoid deliberately draining below the manufacturer’s permitted limit.
Repeat the test under broadly similar conditions. A simple estimate is:
Measured usable capacity = energy delivered during the discharge ÷ change in state of charge
For example, if the system reports energy delivered while moving from 90% to 20%, divide that energy by 0.70 to estimate the equivalent capacity across the full operating range. Treat this as an estimate, not a laboratory measurement. Meter locations, conversion losses, rounding and app refresh delays can all affect the result.
3. Charge, discharge and round-trip efficiency
Round-trip efficiency compares energy taken into the battery with energy later recovered from it. A basic calculation is:
Round-trip efficiency = energy discharged ÷ energy charged × 100
Use readings from the same measurement point where possible. If one value is measured on the DC side and the other on the AC side, the calculation may include different inverter losses and should not be compared casually with previous records. Look for a sustained change rather than reacting to one result.
4. Temperature, alarms and firmware
Record any temperature shown by the app, particularly if it is outside the manufacturer’s stated operating guidance. Also note warning codes, shutdowns, communication errors, abnormal noise and unexpected changes in charging or discharging power. Save screenshots before clearing an alert.
Record firmware updates and configuration changes. A software update, new tariff schedule, altered backup reserve or inverter setting can change the battery’s behaviour without indicating physical degradation.
5. Warranty evidence
Keep the purchase invoice, installation certificate, commissioning records, serial numbers, warranty terms, service history and monitoring screenshots together. Warranty conditions differ between products and may refer to time, energy throughput, retained capacity, operating conditions or a combination of these. Do not assume that a general industry threshold applies to your battery.
Check whether the warranty requires registration, approved installation, specific operating settings, regular servicing or evidence from the manufacturer’s monitoring platform. If a claim may be needed, contact the installer or manufacturer before carrying out a test that could affect the warranty.
Cadence and checkpoints
A light monthly check is usually sufficient for a domestic system operating normally. Record the key app readings, check for alarms and note whether the battery reached its expected state of charge. A more detailed capacity check can be carried out quarterly or when performance appears to change. Use similar weather, state-of-charge limits and household demand where practical.
Carry out an additional review:
- Before the battery warranty approaches an important deadline.
- After a prolonged shutdown, installer visit or firmware update.
- After repeated power cuts, overheating warnings or communication faults.
- Before adding another battery, an EV charger or changing the hybrid inverter.
- When planning a move, insurance review or major electrical work.
Use this record template for each detailed check:
| Field | Record |
|---|---|
| Date and time | |
| Battery and inverter model | |
| Firmware version | |
| Starting and ending state of charge | |
| Energy charged | |
| Energy discharged | |
| Estimated usable capacity | |
| Estimated round-trip efficiency | |
| Temperature, alarms and settings | |
| Weather and unusual loads | |
| Screenshots or installer notes |
How to interpret changes
Compare trends, not isolated readings. The following pattern guide can help separate likely explanations:
| Observation | Possible explanation | Next step |
|---|---|---|
| Lower output on cloudy days | Insufficient solar generation or high household demand | Compare with a similar day and check energy-flow records |
| Battery stops short of its usual charge | Reserve setting, charge schedule, inverter limit or fault | Review settings and alerts; ask the installer if unchanged |
| Capacity appears lower across repeated tests | Degradation, calibration drift or a measurement difference | Repeat under comparable conditions and retain evidence |
| Energy loss rises while capacity looks stable | Changed conversion conditions, standby use or inverter behaviour | Compare AC/DC measurement points and review firmware |
| Repeated alarms, shutdowns or unusual heat | Potential electrical, thermal or communication problem | Follow the manual and contact a qualified professional promptly |
| App data is missing or inconsistent | Internet, gateway, meter or software issue | Check the monitoring connection; do not treat missing data as zero output |
Capacity loss is more credible when the same test method shows a gradual decline across several checkpoints, while charge and discharge limits remain unchanged. If the battery is still within warranty, report the evidence early. Include dates, readings, screenshots, error codes, firmware information and a clear description of the test conditions.
For related system context, see our guide to reading a solar monitoring app and the checklist for adding a battery or EV charger to existing solar panels. If backup is important, review the separate guidance on planning essential loads during a power cut.
When to revisit
Make the health check part of your normal solar maintenance rather than waiting for a complete failure. Review the basic readings monthly or quarterly, complete a comparable capacity test at least periodically, and bring the record up before a warranty deadline or major system change. Revisit the manufacturer’s documentation whenever the battery, inverter, monitoring platform or firmware changes; the available readings and warranty conditions may not remain the same.
Start with a baseline now: save the current warranty documents, photograph the equipment labels, export available monitoring data and complete one carefully recorded discharge observation. Set a calendar reminder for the next review. If repeated results show material deterioration, unexplained alarms, overheating or a loss of backup capability, stop treating the issue as a performance trend and arrange professional diagnosis. Compare repair, warranty replacement and additional storage only after confirming the battery’s measured condition, compatibility and remaining warranty.